rev. 0.5 march 2012 www.aosmd.com page 1 of 8 AOZ8806 ultra-low capacitance tvs diode general description the AOZ8806 is a transient voltage suppressor array designed to protect high speed data lines such as hdmi, usb 3.0, mddi, sata, and gigabit ethernet from damaging esd events. this device incorporates twelve surge rated, low capacitance steering diodes and a tvs in a single package. during transient conditions, the steering diodes direct the transient to either the positive side of the power supply line or to ground. the AOZ8806 provides a typical line-to-line capacitance of 0.3 pf and low insertion loss up to 6 ghz providing greater signal integrity making it ideally suited for hdmi 1.3, thunderbolt, or usb 3.0 applications, such as digital tvs, dvd players, computing, set-top boxes and mddi applications in mobile computing devices. the AOZ8806 comes in a rohs compliant and halogen free 3.3 mm x 1.3 mm x 0.4 mm 8-lead package and is rated for -40 c to +85 c junction temperature range. features ? esd protection for high-speed data lines: ? iec 61000-4-2, level 4 (esd) immunity test ? air discharge: 15 kv; contact discharge: 15 kv ? iec61000-4-4 (eft) 40 a (5/50 ns) ? iec61000-4-5 (lightning) 4 a (8/20 s) ? human body model (hbm) 24 kv ? array of surge rated diodes with internal tvs diode ? small package saves board space ? protects six i/o lines ? low capacitance between i/o lines: 0.3 pf ? low clamping voltage ? low operating voltage: 5.0 v applications ? hdmi, usb 3.0, mddi, sata, thunderbolt ports ? monitors and flat panel displays ? set-top box ? video graphics cards ? digital video interface (dvi) ? notebook computers typical applications figure 1. usb 3.0 ports figure 2. thunderbolt ports tx0+ tx0- rx0+ rx0- tx1+ tx1- rx1+ rx1- hpd dpp lsr cf2 thunderbolt connector AOZ8806 d+ d- ssrx+ ssrx- sstx+ sstx- usb 3.0 transceiver d+ d- ssrx+ ssrx- sstx+ sstx- usb 3.0 connector AOZ8806 AOZ8806
AOZ8806 rev. 0.5 march 2012 www.aosmd.com page 2 of 8 ordering information aos green products use reduced levels of halogens, and are also rohs compliant. please visit www.aosmd.com/web/quality/rohs_compliant.jsp for additional information. pin configuration absolute maximum ratings exceeding the absolute maximum ratings may damage the device. notes: 1. iec 61000-4-2 discharge with c discharge = 150pf, r discharge = 330 ? . 2. human body discharge per mil-std-883, method 3015 c discharge = 100 pf, r discharge = 1.5 k ? . maximum operating ratings part number ambient temperature range package environmental AOZ8806di-05 -40 c to +85 c 3.3 mm x 1.3 mm x 0.55 mm 8-lead green product 8-lead package (top view) gnd gnd i/o i/o i/o i/o i/o i/o 1 2 3 4 5 6 8 7 parameter AOZ8806di-5 storage temperature (t s ) -65 c to +150 c esd rating per iec61000-4-2, contact (1) 15 kv esd rating per iec61000-4-2, air (1) 15 kv esd rating per human body model (2) 24 kv parameter rating junction temperature (t j ) -40 c to +125 c
AOZ8806 rev. 0.5 march 2012 www.aosmd.com page 3 of 8 electrical characteristics t a = 25c unless otherwise specified. notes : 3. these specificatio ns are guaranteed by desig n and characterization. 4. measurements performed using a 100ns transmission line pulse (tlp) system. symbol parameter symbol parameter i pp maximum reverse peak pulse current i t test current v cl clamping voltage @ i pp v f forward voltage @ i f v rwm working peak reverse voltage p pk peak power dissipation i r maximum reverse leakage current c j max. capacitance @ v r = 0 and f = 1 mhz v br breakdown voltage device device marking v rwm (v) max. v br (v) min. i t = 100 ? a i r (a) max. v f (v) typ. v cl max. (3)(4) c j (pf) i pp = 1 a i pp = 12 a typ. max. AOZ8806di-05 ab 5.0 6.0 1.0 0.85 4.0 9.0 0.6 0.75
rev. 0.5 march 2012 www.aosmd.com page 4 of 8 AOZ8806 typical performance characteristics (t period = 100ns, t r = 1ns) forward voltage vs. forward peak pulse current forward current, i/o - gnd insertion loss (s21) vs. frequency frequency (mhz) i pp (a) 0 2 4 6 8 10 12 14 0 2 4 6 8 10 12 14 forward voltage (v) s21 (db) (t period = 100ns, t r = 1ns) clamping voltage vs. peak pulse current peak pulse current, i pp (a) 2 3 4 5 6 7 8 9 10 0 2 4 6 8 10 12 14 clamping voltage, v cl (v) 10 100 1000 -30 -25 -20 -15 -10 -5 0 time (s) 0.0 -875m 875m 898p voltage (v) hdmi 1.4 eye pattern with AOZ8806
rev. 0.5 march 2012 www.aosmd.com page 5 of 8 AOZ8806 high speed pcb layout guidelines printed circuit board layout is the key to achieving the highest level of surge immunity on power and data lines. the location of the protection devices on the pcb is the simplest and most important design rule to follow. the AOZ8806di devices should be located as close as possible to the noise source. the AOZ8806di device should be placed on all data and power lines that enter or exit the pcb at the i/o connector. in most systems, surge pulses occur on data and power lines that enter the pcb through the i/o connector. placing the AOZ8806di devices as close as possible to the noise source ensures that a surge voltage will be clamped before the pulse can be coupled into adjacent pcb traces. in addition, the pcb should use the shortest possible traces. a short trace length equates to low impedance, which ensures that the surge energy w ill be dissipated by the AOZ8806di device. long sig nal traces will act as antennas to receive energy from fields that are produced by the esd pulse. by keepi ng line lengths as short as possible, the efficiency of the line to act as an antenna for esd related fields is reduced. minimize interconnecting line lengths by placing devices with the most interconnect as close together as possible. the protection circuits should shunt the surge voltage to either the reference or chassis ground. shunting the surge voltage directly to the ic?s signal ground can cause ground bounce. the clamping performance of tvs diodes on a single ground pcb can be improved by minimizing the impedance with relatively s hort and wide ground traces. the pcb layout and ic package parasitic inductances can cause significant overshoot to the tvs?s clamping voltage. the inductance of the pcb can be reduced by using short trace lengths and multiple layers with separate ground and power planes. one effective method to minimize loop problems is to incorporate a ground plane in the pcb design. the AOZ8806di ultra-low capacitance tvs is designed to protect six high speed data transmission lines from transient over-voltages by clamping them to a fixed reference. the low inductance and construction minimizes voltage overshoot during high current surges. when the voltage on the protected line exceeds the reference voltage the internal steering diodes are forward biased, conducting the transient current away from the sensitive circuitry. the AOZ8806di is designed for ease of pcb layout by allowing the traces to run underneath the device. the pinout of the AOZ8806di is designed to simply drop onto the io lines of a high definition multimedia interface (hdmi) or usb 3.0 design without having to divert the signal lines that may add more parasitic inductance. figure 3. layout example . gnd gnd i/o AOZ8806 i/o i/o i/o i/o i/o
AOZ8806 rev. 0.5 march 2012 www.aosmd.com page 6 of 8 package dimensions, 3.3 mm x 1.3 mm x 0.55 mm, 8l note: 1. controlling dimension is millimeters. converted inches dimensions are not necessarily exact. top view bottom view side view recommended land pattern d pin #1 dot by marking c a1 e e e1 b l1 a 0.30 0.25 0.68 1.85 0.25 0.50 .05 0.625 0.92 1.25 symbols a a1 b c d e e e1 l l1 dimensions in millimeters min. 0.50 0.00 0.20 3.25 1.25 0.30 0.54 nom. 0.55 0.02 0.25 0.152 ref 3.30 1.30 0.50 bsc 1.25 bsc 0.38 0.62 max. 0.60 0.05 0.30 3.38 1.38 0.43 0.67 symbols a a1 b c d e e e1 l l1 dimensions in inches min. 0.025 0.000 0.008 0.128 0.049 0.012 0.021 nom. 0.022 0.001 0.010 0.006 ref 0.130 0.051 0.020 bsc 0.049 bsc 0.015 0.024 max. 0.024 0.002 0.012 0.133 0.054 0.017 0.026 unit: mm l
rev. 0.5 march 2012 www.aosmd.com page 7 of 8 AOZ8806 tape and reel dimensions, 3. 3 mm x 1.3 mm x 0.55 mm, 8l carrier tape reel leader/trailer and orientation package 3.3x1.3x0.55 b0 3.55 0 .05 a0 1.60 0 .10 k0 0.60 0 .05 d0 1.55 max. d1 1.5 0.1/-0.0 e1 1.75 0 .10 e 12.0 0 .30 e2 5.50 0 .10 p0 4.0 0 .10 p1 4.0 0 .10 p2 2.0 0 .10 p2 p0 a t b0 k0 a0 d0 unit: mm feeding direction t 0.25 0 .05 tape size 12 reel size ?330 m ?330 0 .3/-4.0 n 55.0 0.40 h 13.0 0 .20 w1 12.4 0 .20 s 2.2 0 .20 k 10.6 0 .20 unit: mm r ---- trailer tape 300mm min. a - a? section d1 p1 a e1 e2 e components tape orientation in pocket leader tape
AOZ8806 rev. 0.5 march 2012 www.aosmd.com page 8 of 8 part marking pnwlt part number code assembly lot code week and year code AOZ8806di-05 (3.3 x 1.3 x 0.55 dfn) as used herein: 1. life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body or (b) support or sustain life, and (c) whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury of the user. 2. a critical component in any component of a life support, device, or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. this datasheet contains preliminary data; supplementary data may be published at a later date. alpha & omega semiconductor reserves the right to make changes at any time without notice. life support policy alpha & omega semiconductor products ar e not authorized for use as critical components in life support devices or systems.
|
